Site Management and Remote Monitoring

Victron Cerbo GX and GX Touch

The Victron Cerbo GX is the communication centre of a Victron energy system. It links inverter/chargers, solar charge controllers, battery monitors and supported third-party devices, so you can monitor and control the whole installation from one place, on site or from anywhere through the free Victron Remote Management (VRM) portal. Two versions...

Read More

The Victron Cerbo GX is the communication centre of a Victron energy system. It links inverter/chargers, solar charge controllers, battery monitors and supported third-party devices, so you can monitor and control the whole installation from one place, on site or from anywhere through the free Victron Remote Management (VRM) portal.

Two versions are available. Depending on the load, the Cerbo GX MK3 is three to four times faster than the MK2, which suits systems that need maximum processing power: heavy Node-RED automation, Signal K, or many devices connected over VE.Direct and USB, PV inverters, or both.

The optional GX Touch 50 and GX Touch 70 add a five-inch or seven-inch waterproof touchscreen that gives an instant overview of system status and lets you adjust settings directly on screen. Each display connects with a single cable and comes in top/wall-mount or flush-mount versions, so it can be bolted to a dashboard without cutting a precise opening.

The Cerbo GX itself mounts on a wall, or on a 35mm DIN rail with the optional DIN35 adapter small. It connects to VE.Bus inverter/chargers and to VE.Can and VE.Direct devices, reads tank levels, temperatures and digital inputs, and has two programmable relays for tasks such as generator start/stop. Built-in Bluetooth gives a quick initial connection and network setup with the VictronConnect app.

Victron designs the Cerbo GX for marine systems, with MFD, NMEA 2000 and Signal K integration; energy storage systems, with scheduled charging and peak shaving; off-grid systems, where it prioritises solar and automates generator start/stop; and hybrid generator sites managed remotely through VRM.

Pair it with a Victron BMV-712 Smart battery monitor, SmartSolar MPPT solar charge controllers or a Victron Quattro inverter/charger to build a fully monitored system.

Show Less

Model:
Unit Price
—
or send a quick enquiry about this product only

This product has compatible accessories — view accessories ↓

Features
  • Remote Monitoring via VRM: Brings the complete installation online through any web browser or the VRM app, with data logged continuously, even when the internet connection is temporarily lost.
  • No Subscription Needed: VRM is free for any number of installations and needs no additional hardware, software or subscription.
  • Remote Control: Set the shore power input current limit, start and stop a generator, switch relays, adjust ESS settings and operate inverter/chargers from the same controls as on the device.
  • Fewer Site Visits: Follow up alerts, run diagnostic checks and apply firmware updates and VEConfigure changes remotely.
  • Alarms and History: Reports alarms by email or push notification, and keeps historical data available for analysis.
  • Choose Your Processing Power: The MK3 is three to four times faster than the MK2 depending on load, and supports up to 25 VE.Direct devices compared with 15 for the MK2.
  • Local Access Without Internet: Remote Console gives full access to the user interface over the LAN or the Cerbo GX WiFi access point when there is no internet on site.
  • Connects the Whole System: 3 isolated VE.Direct ports, 2 isolated VE.Bus RJ45 sockets, VE.Can (VE.Can 1 isolated), 10/100 Ethernet, built-in WiFi and 3 USB host ports.
  • Sensor Inputs: Four resistive tank level inputs, four temperature sense inputs and four digital inputs.
  • Programmable Relays: Two NO/NC relays; Relay 1 can act as an alarm relay, generator start/stop, tank pump, temperature-controlled relay or manual switch.
  • Optional Touchscreen: GX Touch 50 (800 x 480) or GX Touch 70 (1024 x 600) display connects with a single 2m cable.
  • Display Built for Harsh Locations: GX Touch top/wall-mount versions are IP54 (without connectors), and flush-mount versions are IP65 when installed with the included rubber gasket.
  • Quick Setup: Built-in Bluetooth connects to the VictronConnect app for initial connection and network configuration.
  • Flexible Mounting: Wall mount, or 35mm DIN rail with the DIN35 adapter small (sold separately).
  • Wide Supply Range: 8–70Vdc supply, drawing 2.8W at 12V without the GX Touch.
  • Approved for Vehicles: ECE R10-6 automotive approval, alongside IEC 62368-1 safety and EN 301489-1/-17 EMC compliance.
Specifications
GENERAL
Parameter Cerbo GX MK2 Cerbo GX MK3
Part number BPP900450110 BPP900451130
Supply voltage 8–70Vdc
Power draw without GX Touch 2.8W @ 12V
Power draw with GX Touch Backlight off: 3.8W @ 12V
Backlight at max: 4.8W @ 12V
Mounting Wall or DIN rail (35mm)
DIN rail mounting requires an additional accessory: DIN35 adapter small
COMMUNICATION PORTS
Parameter Cerbo GX MK2 Cerbo GX MK3
VE.Direct ports (always isolated) 3 (max. possible VE.Direct devices: 15) 3 (max. possible VE.Direct devices: 25)
VE.Bus (always isolated) 2 paralleled RJ45 sockets
VE.Can Yes
VE.Can 1 isolated
VE.Can 2 non-isolated
BMS-Can port Yes – see VE.Can
Bluetooth Yes
Ethernet 10/100 RJ45 socket – isolated except shield
WiFi Built-in
USB 3 USB host ports
VE.Direct maximum: the total of connected VE.Direct devices such as MPPT solar charge controllers, counting all directly connected devices plus the devices connected over USB. The limit is mostly bound by CPU processing power. There is also a limit to other device types of which several are often connected, such as PV inverters.
Bluetooth: intended to assist with initial connection and network configuration. Bluetooth cannot be used to connect to other Victron products (e.g. SmartSolar charge controllers).
IO
Parameter Cerbo GX MK2 Cerbo GX MK3
Resistive tank level inputs 4
Temperature sense inputs 4
Digital inputs 4
Relays 2 x NO/NC
DC up to 30Vdc: 6A
DC up to 70Vdc: 1A
AC: 6A, 125Vac
Relay 1 can be programmed as an alarm relay, generator start/stop, tank pump, temperature-controlled relay or manual operation. Relay 2 is available for programming as a temperature-controlled relay or manual operation in the Relay menu of the GX (requires firmware 2.80 or higher).
MECHANICAL & ENVIRONMENTAL
Parameter Cerbo GX MK2 Cerbo GX MK3
Outer dimensions (h x w x d) 78 x 154 x 48mm
Operating temperature range –20°C to +50°C
IP rating IP20
STANDARDS
Parameter Cerbo GX MK2 Cerbo GX MK3
Safety IEC 62368-1
EMC EN 301489-1
EN 301489-17
Automotive ECE R10-6
GX TOUCH 50 / 70 DISPLAY (OPTIONAL)
Parameter GX Touch 50 / GX Touch 70 GX Touch 50 Flush / GX Touch 70 Flush
Mounting Top/wall mount with included mounting accessories Flush mount or embossed (totally flush)
Protection cover Included with every GX Touch from serial number HQ2242
Also sold individually:
BPP900462050: GX Touch 50 protection cover
BPP900462070: GX Touch 70 protection cover
No
Display resolution GX Touch 50: 800 x 480
GX Touch 70: 1024 x 600
IP rating IP54 (without connectors) IP65 (when installed with the included rubber gasket)
Outer dimensions (h x w x d) GX Touch 50: 87 x 128 x 12.4mm
GX Touch 70: 113 x 176 x 13.5mm
GX Touch 50 Flush: 94 x 136 x 12mm
GX Touch 70 Flush: 120 x 184 x 13mm
Cable length 2m
OPTIONAL ACCESSORIES
GX Touch adapter for CCGX cut-out Replaces a CCGX display with the GX Touch 50 or GX Touch 70. Contents: metal bracket, plastic bezel and four mounting screws.
DIN35 adapter small DIN rail adapter to mount the Cerbo GX on a DIN rail.
Temperature sensor Temperature sensor for Quattro, MultiPlus and GX devices such as the Cerbo GX.
Selection Table
Model Part number Supply voltage Max. VE.Direct devices
Cerbo GX MK2 BPP900450110 8–70Vdc 15
Cerbo GX MK3 BPP900451130 8–70Vdc 25
Downloads
Victron-Cerbo-GX-and-GX-Touch-Datasheet.pdf
Warranty & Returns

Warranty periods vary by product. Please refer to the Powerbox Warranty Policy for the applicable coverage period against manufacturing defects from date of purchase. For returns and RMA requests, please visit our RMA support page or contact our support team directly.

FAQs
It's the communication centre of a Victron system. It connects inverter/chargers, solar charge controllers, battery monitors and supported third-party devices, and lets you monitor and control the whole installation locally or remotely through the free VRM portal, a GX Touch display, a marine MFD or the VictronConnect app.
Depending on the load, the MK3 is three to four times faster than the MK2, and it supports up to 25 VE.Direct devices compared with 15 for the MK2. Choose the MK3 for heavy Node-RED automation, Signal K, or systems with many devices on VE.Direct and USB, PV inverters, or both. The MK2 part number is BPP900450110 and the MK3 is BPP900451130.
No. The GX Touch 50 and GX Touch 70 are optional. Without a display you can use the Cerbo GX through the VRM portal, Remote Console over the LAN or the Cerbo GX WiFi access point, a marine MFD or the VictronConnect app.
The GX Touch 50 is a five-inch display with 800 x 480 resolution and the GX Touch 70 is a seven-inch display with 1024 x 600 resolution. Both come in top/wall-mount (IP54 without connectors) and flush-mount (IP65 with the included rubber gasket) versions, and both connect with a 2m cable.
No. VRM is free for any number of installations and needs no additional hardware, software or subscription. Monitoring, alerts, remote control and remote maintenance are available as soon as the Cerbo GX is online.
It runs from 8–70Vdc and draws 2.8W at 12V without a GX Touch, or 3.8W (backlight off) to 4.8W (backlight at maximum) at 12V with a GX Touch connected.
Yes. It has two programmable NO/NC relays. Relay 1 can be set up as an alarm relay, generator start/stop, tank pump, temperature-controlled relay or manual switch, and Relay 2 as a temperature-controlled relay or manual switch (firmware 2.80 or higher). Relay contacts are rated 6A up to 30Vdc, 1A up to 70Vdc and 6A at 125Vac.
Yes, on a 35mm DIN rail using the DIN35 adapter small, which is sold separately. It can also be wall mounted.
No. Bluetooth is intended for the initial connection and network configuration with the VictronConnect app. It can't be used to connect to other Victron products such as SmartSolar charge controllers.
It complies with IEC 62368-1 (safety), EN 301489-1 and EN 301489-17 (EMC) and ECE R10-6 (automotive). It operates from –20°C to +50°C and is rated IP20. For selection help, contact Powerbox at sales@powerbox.co.nz.