Site Management and Remote Monitoring

Victron BMV-712 Smart Battery Monitor

The Victron BMV-712 Smart is a precision battery monitor with Bluetooth built in. It acts as a fuel gauge for your battery bank, tracking voltage, current, power, ampere-hours consumed and state of charge, and shows how much time is left at the current rate of discharge. Using the VictronConnect app on a smartphone or other Bluetooth-enabled dev...

Read More

The Victron BMV-712 Smart is a precision battery monitor with Bluetooth built in. It acts as a fuel gauge for your battery bank, tracking voltage, current, power, ampere-hours consumed and state of charge, and shows how much time is left at the current rate of discharge. Using the VictronConnect app on a smartphone or other Bluetooth-enabled device, you can customise settings, see all the important data on a single screen, review historical data and update the software as new features become available.

Installation is simple. All electrical connections are made to the quick-connect PCB on the included 500A shunt, which links to the flush-mounted display with a standard RJ12 cable. The RJ12 cable, a fused battery cable and a front bezel for a square or round appearance are all supplied, so no other components are needed.

An auxiliary input measures the voltage of a second battery, battery temperature or the midpoint voltage of a series-connected bank. Midpoint monitoring gives early warning of one bad cell or battery before it destroys a large, expensive bank. The programmable bistable relay can switch off non-critical loads or start a generator when needed, without adding current draw during an alarm, and the monitor's very low self-consumption helps protect lithium-ion batteries left in a discharged state. The BMV-712 Smart Battery Monitor also meets the ECE R10-4 automotive EMC standard.

For system-wide monitoring, the VE.Direct port connects the BMV-712 Smart to a Victron Color Control GX, where data can be stored and analysed on the VRM Portal. Victron recommends its Battery Balancer to maximise the service life of series-connected lead-acid batteries. For systems that don't need Bluetooth, see the Victron BMV-700 series battery monitors, or browse the complete Victron Energy range.

Show Less

Model:
Unit Price
—
or send a quick enquiry about this product only
Features
  • Bluetooth Built In: Customise settings, see all key data on one screen, view historical data and update software from a smartphone or other Bluetooth-enabled device.
  • Battery Fuel Gauge: Tracks battery voltage, current, power, ampere-hours consumed and state of charge, plus remaining time at the current rate of discharge.
  • Midpoint Voltage Monitoring: Measures the midpoint voltage of series-connected batteries, giving timely warning of one bad cell or battery before it damages the whole bank.
  • Auxiliary Input: Measures the voltage of a second battery, battery temperature (with the optional sensor) or midpoint voltage, with corresponding alarm and relay settings.
  • Very Low Current Draw: 0.7Ah per month (1mA) at 12V and 0.6Ah per month (0.8mA) at 24V, helping protect lithium-ion batteries left in a discharged state.
  • Bistable Alarm Relay: Programmable 60V/1A relay switches off non-critical loads or starts a generator, and its bistable design prevents increased current draw during an alarm.
  • Programmable Alarms: Visual and audible alarms alert you to battery conditions that need attention.
  • High-Resolution Measurement: 10mA (0.01A) current resolution, with ±0.4% current and ±0.3% voltage accuracy using the included 500A shunt.
  • Scales to Large Battery Banks: Shunt selection capability up to 10,000A, with optional 1,000A, 2,000A and 6,000A shunts that accept the standard quick-connect PCB.
  • Wide Supply Range: 6.5–70Vdc supply covers 12V, 24V and 48V battery systems.
  • Stored Trends and History: Keeps 46 days of trend data and a wide range of historical events, so you can evaluate usage patterns and battery health.
  • System Integration via VE.Direct: Connects to a Color Control GX, with up to four BMVs directly connected and more through a USB hub, and data stored and analysed on the VRM Portal.
  • Easy Installation: All connections are made at the quick-connect PCB on the shunt, and the 10m RJ12 cable and 2m fused battery cable are included, so no other components are needed.
  • Flexible Mounting: Flush mounts with a 63mm round front, with a separate bezel for a square or round display appearance, a securing ring for rear mounting and screws for front mounting.
Specifications
GENERAL SPECIFICATIONS
Supply voltage range 6.5–70Vdc
Current draw, backlight off <1mA
Current consumption 0.7Ah per month (1mA) at 12V; 0.6Ah per month (0.8mA) at 24V
Input voltage range, auxiliary battery 6.5–70Vdc
Battery capacity 1–9,999Ah
Operating temperature range –40°C to +50°C (–40°F to 120°F)
Measures voltage of second battery, temperature or midpoint Yes
Temperature measurement range –20°C to +50°C
Current measurement resolution 10mA (0.01A)
Shunt selection capability Up to 10,000A
Bluetooth Built-in
VE.Direct communication port Yes
Bistable relay 60V / 1A normally open (function can be inverted)
RESOLUTION & ACCURACY (with a 500A shunt)
Current ±0.01A
Voltage ±0.01V
Amp hours ±0.1Ah
State of charge (0–100%) ±0.1%
Time to go ±1min
Temperature (0–50°C or 30–120°F) ±1°C/°F
Accuracy of current measurement ±0.4%
Accuracy of voltage measurement ±0.3%
INSTALLATION & DIMENSIONS
Installation Flush mount
Front 63mm diameter
Front bezel 69 x 69mm (2.7 x 2.7 inch)
Shunt connection bolts M10 (0.3937 inch)
Body diameter and depth 52mm (2.0 inch) and 31mm (1.2 inch)
Protection category IP55 (not intended for outdoor use)
STANDARDS
Safety EN 60335-1
Emission / Immunity EN 55014-1 / EN 55014-2
Automotive ECE R10-4 / EN 50498
ACCESSORIES
Shunt (included) 500A / 50mV
Cables (included) 10m 6-core UTP cable with RJ12 connectors, and 2m battery cable with 1A slow-blow fuse for '+' connection
Mounting kit (included) Separate front bezel for a square or round display appearance, securing ring for rear mounting and screws for front mounting
Temperature sensor Optional (ASS000100000)
Optional shunts 1,000A/50mV, 2,000A/50mV and 6,000A/50mV (the quick-connect PCB on the standard 500A/50mV shunt can also be mounted on these shunts)
Interface cables VE.Direct cables to connect to a Color Control GX (ASS030530xxx); VE.Direct to USB interface (ASS030530000) to connect several BMVs to a Color Control GX or computer
Battery Balancer Optional (BMS012201000), recommended to maximise the service life of series-connected lead-acid batteries
STORED TRENDS
Data stored Battery voltage, current and state of charge (%), plus the auxiliary input (battery temperature, midpoint deviation or starter battery voltage)
Number of days trends data is stored 46
Downloads
Victron-BMV-712-Smart-Battery-Monitor-Datasheet.pdf
Warranty & Returns

Warranty periods vary by product. Please refer to the Powerbox Warranty Policy for the applicable coverage period against manufacturing defects from date of purchase. For returns and RMA requests, please visit our RMA support page or contact our support team directly.

FAQs
It tracks battery voltage, current, power, ampere-hours consumed and state of charge, and shows the remaining time at the current rate of discharge. Built-in Bluetooth lets you monitor and configure it from a smartphone with the VictronConnect app.
No. Bluetooth is built in, so a smartphone or other Bluetooth-enabled device can connect to it directly to customise settings, view data and history, and update the software.
The monitor, a 500A/50mV shunt with quick-connect PCB, a 10m six-core UTP cable with RJ12 connectors, a 2m battery cable with a 1A slow-blow fuse for the '+' connection, a separate front bezel for a square or round appearance, a securing ring for rear mounting and screws for front mounting.
All electrical connections are made to the quick-connect PCB on the shunt, which connects to the monitor with the supplied RJ12 cable. The monitor flush mounts with a 63mm diameter front and 52mm body diameter. Refer to the Victron BMV manual for full wiring instructions.
It operates from a 6.5–70Vdc supply, which covers 12V, 24V and 48V battery systems.
Yes. Its auxiliary input can measure the voltage of a second battery, such as a starter battery, alongside the main battery bank. The same input can instead be used for battery temperature or midpoint voltage.
It measures the voltage at the midpoint of series-connected batteries. One bad cell or battery can destroy a large, expensive bank, and a midpoint alarm gives a timely warning so you can act before that happens. Victron's BMV manual, section 5.2, has more detail.
Yes, using the auxiliary input with the optional temperature sensor (ASS000100000). The temperature measurement range is –20°C to +50°C.
0.7Ah per month (1mA) at 12V and 0.6Ah per month (0.8mA) at 24V. This very low draw matters for lithium-ion batteries, which can be damaged if a residual load drains them after a low-voltage shutdown.
Yes. It ships with a 500A/50mV shunt and supports shunts up to 10,000A. Optional 1,000A/50mV, 2,000A/50mV and 6,000A/50mV shunts accept the quick-connect PCB from the standard shunt.
Yes. Its programmable 60V/1A bistable relay (normally open, function can be inverted) can turn off non-critical loads or run a generator when needed.
It stores 46 days of trend data covering battery voltage, current, state of charge and the auxiliary input, plus a wide range of historical events.
Yes. Its VE.Direct port connects to a Color Control GX with a VE.Direct cable (ASS030530xxx). Up to four BMVs connect directly, more can be added through a USB hub with VE.Direct to USB interfaces (ASS030530000), and data can be stored and analysed on the VRM Portal.
It operates from –40°C to +50°C and is rated IP55, but it isn't intended for outdoor use.